Download PDF
← Technical datasheet
Gedik · Low-alloy steels
FERVEO

TEMPO B 75 — E 10018 - G H4

Technical datasheet · covered electrode · stick electrode · Ø 2.5 – 5 mm
FT-TEMPO-B-75-EN
rev. 2 · 2026-11-21
page 1 / 2
Type
covered electrode · stick electrode
Standard
E 10018 - G H4
Diameters
Ø 2.5 – 5 mm
Sizes and packaging
Ø
Length
Current
Code
2.5 mm
350 mm
80–110 A
GDK-3010100582
3.2 mm
350 mm
100–140 A
GDK-3010100585
4 mm
450 mm
130–190 A
GDK-3010100588
5 mm
450 mm
190–240 A
GDK-3010100591
Application
  • Content of Mn-Mo-Ni alloy
  • High ductility and high resistance to cracking obtained in welding high-strength, quenched and tempered, fine-grained structural steels
  • Suitability for use in welding of materials with service temperatures between -60°C and +400°C
  • Very high values of impact resistance after aging
  • Convenience of welding at all positions except for the vertical down position.
  • Possibility of applying same heat treatment temperatures at pre- and post-welding as well as at transition stages as those of base metal
  • Weld deposits with very low contents of hydrogen
  • Requirement of re-drying for minimum 2 hours at the temperatures between 300°C and 350°C
Classification
AWS class
E 10018 - G H4
EN ISO class
E 62 6 Z 1NiMo B 4 2 H5
Approvals

CE, SEPRO

Validity is confirmed with the order

Chemical composition of the weld metal
C
Cr
Mn
Mo
Ni
Si
0.05
0.30
1.30
0.50
1.30
0.50
Values in mass %.
Base metals

The yield strength of 620 N/mm2 up to the quenched and tempered fine grain steels · 780 N/mm2 heat treating steels

QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-TEMPO-B-75-EN · rev. 2 · page 1 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue

Gedik · Low-alloy steels
FERVEO

TEMPO B 75 — E 10018 - G H4

Technical datasheet · covered electrode · stick electrode · Ø 2.5 – 5 mm
FT-TEMPO-B-75-EN
rev. 2 · 2026-11-21
page 2 / 2
Mechanical properties
after heat treatment: 560–600 °C / 1 h / 300 °C (air)
Yield strength (Rp0.2)
min. 620 MPa
Tensile strength (Rm)
690–890 MPa
Elongation (A5)
min. 18 %
Impact energy (KV)
min. 47 J (−60 °C)
Process
Polarity
DC+
Positions
PA flat · PB horizontal-vertical · PC horizontal · PD horizontal-overhead · PE overhead · PF vertical-up
Treatment and preparation
Re-drying
300–350 °C / min. 2 h
Post-weld heat treatment
possible at the same temperatures as the base metal
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-TEMPO-B-75-EN · rev. 2 · page 2 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue