Download PDF
← Technical datasheet
Gedik · Creep-resisting Cr-Mo steels
FERVEO

SG Mo TIG — ER 80 S-G (mod.) (ER 70 S-A1)

Technical datasheet · TIG rod · Ø 1.6 – 4 mm
FT-SG-MO-TIG-EN
rev. 2 · 2026-11-21
page 1 / 2
Type
TIG rod
Standard
ER 80 S-G (mod.) (ER 70 S-A1)
Diameters
Ø 1.6 – 4 mm
Sizes and packaging
Ø
Length
Packaging
Code
1.6 mm
1000 mm
5 kg
GDK-3010300421
2 mm
1000 mm
5 kg
GDK-3010300422
2.4 mm
1000 mm
5 kg
GDK-3010300423
3.2 mm
1000 mm
5 kg
GDK-3010300424
4 mm
1000 mm
5 kg
GDK-3010300425
Application
  • Copper coated wire for GMAW and rod TIG welding in boiler pressure vessel, pipework and crane construction as well as in structural steel engineering
  • High quality, very tough deposit of high crack resistance and non-aging
  • Recommended for service in temperature range (-40°C) for TIG, or (-20°C) for GMAW to (+550°C)
  • Good copper bonding with low total copper content. Very good welding and flow characteristics
  • Preheating interpass and postweld heat treatment as required by base metal
  • Shielding gases: MAG; Ar+CO2, mix gases, TIG; %100 Ar
Classification
AWS class
ER 80 S-G (mod.) (ER 70 S-A1)
EN ISO class
W MoSi
Approvals

CE, SEPRO

Validity is confirmed with the order

Chemical composition of the wire
C
Mn
Mo
Si
0.10
1.10
0.50
0.60
Values in mass %.
Base metals

S355J2G3 · L320-L415NB · L320MB-L415MB · P255G1TH · P235GH-P355GH · P255NH · 16Mo3 · 17MnMoV6-4 · 20MnMoNi5-5 · 20MnMoNi4-5 · GE240-GE300 · 22Mo4 · S255N-S460N · P255NH-P460 NH

QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-SG-MO-TIG-EN · rev. 2 · page 1 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue

Gedik · Creep-resisting Cr-Mo steels
FERVEO

SG Mo TIG — ER 80 S-G (mod.) (ER 70 S-A1)

Technical datasheet · TIG rod · Ø 1.6 – 4 mm
FT-SG-MO-TIG-EN
rev. 2 · 2026-11-21
page 2 / 2
Mechanical properties
Yield strength (Rp0.2)
min. 460 MPa
Tensile strength (Rm)
550–670 MPa
Elongation (A5)
min. 22 %
Impact energy (KV)
min. 47 J (−20 °C)
Process
Polarity
DC−
Shielding gas
100% Ar
Positions
PA flat · PB horizontal-vertical · PC horizontal · PD horizontal-overhead · PE overhead · PF vertical-up · PG vertical-down
Shielding
Requires shielding gas
Treatment and preparation
Pre-heating
as required by the base metal
Interpass temperature
as required by the base metal
Post-weld heat treatment
as required by the base metal
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-SG-MO-TIG-EN · rev. 2 · page 2 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue