Download PDF
← Technical datasheet
Gedik · Creep-resisting Cr-Mo steels
FERVEO

SG 80 S-D2 MIG — ER 80 S-D2

Technical datasheet · solid wire · Ø 0.8 – 1.6 mm
FT-SG-80-S-D2-MIG-EN
rev. 2 · 2026-11-21
page 1 / 2
Type
solid wire
Standard
ER 80 S-D2
Diameters
Ø 0.8 – 1.6 mm
Application
  • Copper coated for GMAW and TIG welding in boiler pressure vessel, pipework and crane construction as well as in structural steel engineering
  • High quality, very tough deposit of high crack resistance and non-aging
  • Recommended for service in temperature range -45°C (TIG) or -40 °C (GMAW) to +550 °C.
  • Good copper bonding with low total copper content
  • Very good welding and flow characteristics
  • Preheating interpass and postweld heat treatment as required by base metal
  • Shielding gases: MAG; Ar+CO2 mix gases, TIG; pure Ar gas can be used
Classification
AWS class
ER 80 S-D2
EN ISO class
G 4Mo
Approvals

CE, SEPRO

Validity is confirmed with the order

Chemical composition of the wire
C
Mn
Mo
Si
0.10
1.80
0.50
0.65
Values in mass %.
Base metals

S355J2G3 · L320-L415NB · L320MB-L415MB · P255G1TH · P235GH-P355GH · 16Mo3 · 17MnMoV6-4 · 20MnMoNi5-5 · 20MnMoNi4-5 · GE240-GE300 · 22Mo4 · S255N-S460N · P255NH-P460 NH

Mechanical properties
Yield strength (Rp0.2)
min. 470 MPa
Tensile strength (Rm)
550–680 MPa
Elongation (A5)
min. 20 %
Impact energy (KV)
min. 47 J (−30 °C)
Process
Polarity
DC+
Shielding gas
Ar + CO2
Positions
PA flat · PB horizontal-vertical · PC horizontal · PD horizontal-overhead · PE overhead · PF vertical-up · PG vertical-down
Shielding
Requires shielding gas
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-SG-80-S-D2-MIG-EN · rev. 2 · page 1 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue

Gedik · Creep-resisting Cr-Mo steels
FERVEO

SG 80 S-D2 MIG — ER 80 S-D2

Technical datasheet · solid wire · Ø 0.8 – 1.6 mm
FT-SG-80-S-D2-MIG-EN
rev. 2 · 2026-11-21
page 2 / 2
Sizes and packaging
Ø
Packaging
Code
0.8 mm
BS 300
GDK-3010203050
0.8 mm
D 300
GDK-3010203075
1 mm
BS 300
GDK-3010203052
1 mm
D 300
GDK-3010203077
1.2 mm
BS 300
GDK-3010203054
1.2 mm
D 300
GDK-3010203079
1.6 mm
BS 300
GDK-3010203055
1.6 mm
D 300
GDK-3010203081
Treatment and preparation
Pre-heating
as required by the base metal
Interpass temperature
as required by the base metal
Post-weld heat treatment
as required by the base metal
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-SG-80-S-D2-MIG-EN · rev. 2 · page 2 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue