Download PDF
← Technical datasheet
Gedik · Aluminium
FERVEO

AlMg 5 TIG — ER 5356

Technical datasheet · TIG rod · Ø 1.6 – 2.4 mm
FT-ALMG-5-TIG-EN
rev. 2 · 2026-11-21
page 1 / 2
Type
TIG rod
Process
TIG welding · gas welding
Standard
ER 5356
Diameters
Ø 1.6 – 2.4 mm
Sizes and packaging
Ø
Length
Packaging
Code
1.6 mm
1000 mm
5 kg
GDK-6011100062
2 mm
1000 mm
5 kg
GDK-6011100281
2.4 mm
1000 mm
5 kg
GDK-6011100282
Application
  • AIMg5 is magnesium alloyed aluminum TIG rod
  • It is used for joining of aluminum alloys required high mechanical properties
  • The weld deposit has a good resistance to atmospheric influences and sea water
  • And the weld metal is proper for surface treatment such as anodizing and polishing
  • it is recommended that preheating to 150°C before welding of plates thicker than 15mm
  • For gas welding, GeKaTec F-LH1 is recommended
  • Shielding gas: Ar
Classification
AWS class
ER 5356
EN ISO class
S Al 5356 (AlMg5Cr(A))
Welding process
TIG welding · gas welding
Approvals

SEPRO

Validity is confirmed with the order

Chemical composition of the wire
Al
Mg
Mn
Si
balance
5.00
0.50
0.50
Values in mass %.
Mechanical properties
Yield strength (Rp0.2)
120 MPa
Tensile strength (Rm)
250 MPa
Elongation (A5)
25 %
Hardness
70 HB
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-ALMG-5-TIG-EN · rev. 2 · page 1 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue

Gedik · Aluminium
FERVEO

AlMg 5 TIG — ER 5356

Technical datasheet · TIG rod · Ø 1.6 – 2.4 mm
FT-ALMG-5-TIG-EN
rev. 2 · 2026-11-21
page 2 / 2
Process
Polarity
AC
Shielding gas
Ar
Positions
PA flat · PB horizontal-vertical · PC horizontal · PD horizontal-overhead · PE overhead · PF vertical-up · PG vertical-down
Shielding
Requires shielding gas
Treatment and preparation
Pre-heating
150 °C, for plates thicker than 15 mm
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-ALMG-5-TIG-EN · rev. 2 · page 2 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue