Download PDF
← Technical datasheet
Gedik · Low-alloy steels
FERVEO

TEMPO Ni Cu — E7018-G/7018-W1(mod.)H4

Technical datasheet · covered electrode · stick electrode · Ø 2.5 – 5 mm
FT-TEMPO-NI-CU-EN
rev. 2 · 2026-11-21
page 1 / 2
Type
covered electrode · stick electrode
Standard
E7018-G/7018-W1(mod.)H4
Diameters
Ø 2.5 – 5 mm
Sizes and packaging
Ø
Length
Current
Code
2.5 mm
350 mm
80–110 A
GDK-3010100636
3.2 mm
350 mm
130–150 A
GDK-3010100639
4 mm
450 mm
150–190 A
GDK-3010100645
5 mm
450 mm
200–250 A
GDK-3010100648
Application
  • Content of Ni-Cu-Cr alloy
  • Suitability for use in welding structural steels exposed to weathering, such as COR-TEN.
  • High mechanical properties with excellent crack resistance
  • Convenience of welding at all positions except for vertical down position
  • Weld deposits with very low contents of hydrogen
  • Requirement of re-drying for minimum 2 hours at the temperatures between 300°C and 350°C
Classification
AWS class
E7018-G/7018-W1(mod.)H4
EN ISO class
E 42 3 Z NiCrCu B 42 H5
Approvals

TSE, CE, SEPRO

Validity is confirmed with the order

Chemical composition of the weld metal
C
Cr
Cu
Mn
Ni
Si
0.06
0.30
0.40
1.00
0.40
0.50
Values in mass %.
Base metals

S235JR · S235JRW · S325J2W · S355J2G1W · S355JRW · S355J2G 3 Cu · COR-TEN A

QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-TEMPO-NI-CU-EN · rev. 2 · page 1 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue

Gedik · Low-alloy steels
FERVEO

TEMPO Ni Cu — E7018-G/7018-W1(mod.)H4

Technical datasheet · covered electrode · stick electrode · Ø 2.5 – 5 mm
FT-TEMPO-NI-CU-EN
rev. 2 · 2026-11-21
page 2 / 2
Mechanical properties
Yield strength (Rp0.2)
min. 420 MPa
Tensile strength (Rm)
510–630 MPa
Elongation (A5)
min. 22 %
Impact energy (KV)
min. 47 J (−30 °C)
Process
Polarity
DC+
Positions
PA flat · PB horizontal-vertical · PC horizontal · PD horizontal-overhead · PE overhead · PF vertical-up
Treatment and preparation
Re-drying
300–350 °C / min. 2 h
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-TEMPO-NI-CU-EN · rev. 2 · page 2 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue