Download PDF
← Technical datasheet
Gedik · Low-alloy steels
FERVEO

TEMPO B 2 — E8018-C1 H4

Technical datasheet · covered electrode · stick electrode · Ø 2.5 – 5 mm
FT-TEMPO-B-2-EN
rev. 2 · 2026-11-21
page 1 / 2
Type
covered electrode · stick electrode
Standard
E8018-C1 H4
Diameters
Ø 2.5 – 5 mm
Sizes and packaging
Ø
Length
Current
Code
2.5 mm
350 mm
70–100 A
GDK-3010100681
3.2 mm
350 mm
110–140 A
GDK-3010100684
4 mm
450 mm
140–180 A
GDK-3010100687
5 mm
450 mm
190–230 A
GDK-3010100690
Application
  • Suitability for use in welding fine-grained, Ni-alloyed and carbon steels as well as cryogenic steels
  • High ductility and crack resistance in weld deposits
  • Serviceability of weld metals at temperatures down to -80°C
  • Weld metal recovery of approx. 120%
  • Convenience of welding at all positions except for vertical down position
  • Possibility of applying same heat treatment temperatures at pre- and post-welding as well as at transition stages as those of base metal
  • Weld deposits with very low contents of hydrogen
  • Requirement of re-drying for minimum 2 hours at the temperatures between 300°C and 350°C
Classification
AWS class
E8018-C1 H4
EN ISO class
E 46 6 2 Ni B 42 H5
Approvals

TSE, CE, SEPRO

Validity is confirmed with the order

Chemical composition of the weld metal
C
Mn
Ni
Si
0.05
0.80
2.40
0.30
Values in mass %.
Base metals

12Ni14 · 14Ni6 · 13MnNi6-3 · G12Ni14 · S255N-S460N · S255NH-S460NH · S255NL-S460NL · S255NL1-S460NL 1 · TTSt35 · N · V · TTSt45N/V

QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-TEMPO-B-2-EN · rev. 2 · page 1 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue

Gedik · Low-alloy steels
FERVEO

TEMPO B 2 — E8018-C1 H4

Technical datasheet · covered electrode · stick electrode · Ø 2.5 – 5 mm
FT-TEMPO-B-2-EN
rev. 2 · 2026-11-21
page 2 / 2
Mechanical properties
after heat treatment: 605 °C / 2 h / 300 °C (air)
Yield strength (Rp0.2)
min. 460 MPa
Tensile strength (Rm)
550–690 MPa
Elongation (A5)
min. 20 %
Impact energy (KV)
min. 47 J (−80 °C)
Process
Polarity
DC+
Positions
PA flat · PB horizontal-vertical · PC horizontal · PD horizontal-overhead · PE overhead · PF vertical-up
Recovery
approx. 120 %
Treatment and preparation
Re-drying
300–350 °C / min. 2 h
Post-weld heat treatment
possible at the same temperatures as the base metal
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-TEMPO-B-2-EN · rev. 2 · page 2 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue