Download PDF
← Technical datasheet
Gedik · Aluminium
FERVEO

AlMg 4.5 Mn TIG — ER 5183

Technical datasheet · TIG rod · Ø 2 – 3.2 mm
FT-ALMG-4-5-MN-TIG-EN
rev. 2 · 2026-11-21
page 1 / 2
Type
TIG rod
Process
TIG welding · gas welding
Standard
ER 5183
Diameters
Ø 2 – 3.2 mm
Sizes and packaging
Ø
Length
Packaging
Code
2 mm
1000 mm
5 kg
GDK-6011100284
2.4 mm
1000 mm
5 kg
GDK-6011100393
3.2 mm
1000 mm
5 kg
GDK-6011100285
Application
  • AIMg4.5Mn is Magnesium alloyed Aluminum TIG rod
  • It is used for joining of Aluminum alloys including more than 3% Mg
  • The weld deposit has a good resistance to atmospheric influences and sea water
  • It is recommended that preheating to 150 °C before welding of plates thicker than 15mm
  • For gas welding, GeKaTec F-LH1 is recommended
  • Shielding gas: Ar
Classification
AWS class
ER 5183
EN ISO class
SAl 5183(AlMg4.5Mn0.7A)
Welding process
TIG welding · gas welding
Approvals

SEPRO, CE

Validity is confirmed with the order

Chemical composition of the wire
Al
Cr
Fe
Mg
Mn
Si
balance
0.20
< 0.40
5.00
0.80
< 0.40
Values in mass %.
Mechanical properties
Yield strength (Rp0.2)
170 MPa
Tensile strength (Rm)
250 MPa
Elongation (A5)
20 %
Hardness
45 HB
Process
Polarity
AC
Shielding gas
Ar
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-ALMG-4-5-MN-TIG-EN · rev. 2 · page 1 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue

Gedik · Aluminium
FERVEO

AlMg 4.5 Mn TIG — ER 5183

Technical datasheet · TIG rod · Ø 2 – 3.2 mm
FT-ALMG-4-5-MN-TIG-EN
rev. 2 · 2026-11-21
page 2 / 2
Process (cont.)
Positions
PA flat · PB horizontal-vertical · PC horizontal · PD horizontal-overhead · PE overhead · PF vertical-up · PG vertical-down
Shielding
Requires shielding gas
Treatment and preparation
Pre-heating
150 °C, for plates thicker than 15 mm
QR code for the current version of this datasheet
FERVEO IBERICA, S.L.U. · NIF B05613559 · Avda. del Tomillar, 70, 29631 Benalmádena (Málaga) · Registered in the Registro Mercantil de Málaga, sheet MA-201214 · info@ferveo.eu · www.ferveo.eu · FT-ALMG-4-5-MN-TIG-EN · rev. 2 · page 2 / 2

Typical values, not guaranteed: this document is not a declaration of performance and does not replace the manufacturer's official documentation or the applicable WPS.

Prepared by FERVEO from the Gedik 2023 catalogue